Go Rhino RB Series running board drawing

Quick answer: all three Go Rhino RB Series boards are cab-length running boards made from 16-gauge galvanized steel, sold with vehicle-specific brackets, and listed as no-drill. The difference is the look and the step: RB10 has a 6 in. louvered step with rounded edges, RB20 has a 7.5 in. tapered step with bullet-stamped holes and an angular shape, and RB30 has a 7 in. step with flow-through slots and tapered ends. Each also comes in a Slim Line version that sits closer to the cab. If you want a step that folds away, look at Go Rhino VoltStep electric boards instead.

RB10 vs RB20 vs RB30 at a glance

RB10 RB20 RB30
Step width (standard) 6 in. 7.5 in., tapered 7 in., tapered ends
Slim Line width 4 in. at widest point 5.5 in. at widest point, tapers to the rear 5 in. for most of its length, then tapers
Step surface Stamped louvers with raised edges; drains water, mud and snow Bullet-stamped perforations; snow, mud and moisture pass through Flow-through slots that shed mud and snow
Styling Smoothly rounded edges Sharp lines, angular profile, fully boxed ends Contoured angles, tapered ends
Material 16-gauge galvanized steel
Finishes Protective bedliner coating or textured black powder coat
Install Vehicle-specific brackets to factory mounting points, no drilling; RB10 and RB20 listings say under 60 minutes with basic hand tools

Load: the RB30 listings say the board supports up to 600 lbs. per side (the RB30 Slim Line listing says 300 lbs. per stepping surface, 600 lbs. per board). The RB10 and RB20 listings we carry don't give a load rating.

Which one should you pick?

  • RB10 if you want a rounded, close-to-factory look with a 6 in. step. The louvered tread gives raised edges for grip.
  • RB20 if you want the widest step (7.5 in.) and a more aggressive, angular look.
  • RB30 if you want a wide 7 in. step with tapered ends, which the listing says reduce the spots most likely to catch on rocks and curbs.
  • Any Slim Line if you off-road or have a lifted truck and want the board tucked closer to the cab for more ground clearance, and you're fine with a narrower step.

Bedliner coating or textured black?

Both finishes are offered on all three lines. The bedliner-coated boards use a bonded zinc phosphate base coat under the bedliner coating (two layers of rust protection, per the listings). In part numbers, a T ending is the bedliner finish, PC is textured black powder coat, and an S before the finish code (ST, SPC) is the Slim Line version. For example, 69615587T is the RB30 in bedliner, 69615587PC is the RB30 in textured black, and 69615587ST is the RB30 Slim Line in bedliner.

Kits vs boards only

Most listings are complete kits (boards plus vehicle brackets). Go Rhino also sells boards only (for example RB10 630087T, RB20 69400087T, RB30 69600087T) and brackets only (for example 6941555 RB10/RB20 brackets and 6941556 RB30 and RB Slim brackets for the 2015–2027 F-150). If you buy boards only, match the bracket kit to your truck and cab.

Part numbers for popular trucks

Truck (cab) RB10 / RB10 Slim RB20 / RB20 Slim RB30 / RB30 Slim
2015–2027 F-150 Crew Cab (also listed for 2017–2027 F-250/F-350 Super Duty Crew Cab) 63415587T / 63415587ST 69415587T / 69415587ST 69615587T / 69615587ST
2019–2026 Silverado 1500 Crew Cab (and more, see listing) 63404887T / 63404887ST 69404887T / 69404887ST 69604887T / 69604887ST
2005–2027 Nissan Frontier Crew Cab 63434680T 69434680T See the Go Rhino page

Each part above is shown in the bedliner finish; the textured black versions use the same number with PC in place of T. Always check the Fits line and cab on the product page: several listings say fitment can depend on cab style, trim and factory options. Many more trucks, Jeeps and SUVs are listed on the Go Rhino page and in running boards.

VoltStep electric running boards

Go Rhino VoltStep boards are powered: per the listings, they deploy when a door opens and tuck under the rocker panel when it closes, using magnetic door switches (leaving the OBD port free), dual electric motors on each board, 6 in. aluminum steps with integrated white LED lights, an automatic safe-stop if something is in the board's path, and an interior bypass switch. Examples: 20444587T for the 2022–2026 Tundra Crew Cab, 20450674T for the 2018–2027 Wrangler and 20451687T for the Gladiator Crew Cab.

FAQ

What is the widest Go Rhino RB running board?

The standard RB20, with a 7.5 in. tapered step. The RB30 is 7 in. and the RB10 is 6 in.

What does Slim Line mean on Go Rhino running boards?

A narrower version of the same board that fits tighter to the cab for more ground clearance: RB10 Slim Line is 4 in. at its widest, RB20 Slim Line 5.5 in., and RB30 Slim Line 5 in. for most of its length.

Do Go Rhino RB running boards need drilling?

The RB10, RB20 and RB30 kits we carry are listed as no-drill, mounting to factory attachment points with vehicle-specific brackets. Check the Install line on your exact listing.

Can I add drop steps to RB10 or RB20 boards?

The RB10 and RB20 listings say optional drop-down steps are available, sold separately. Contact us with your truck and board part number and we'll help match them.

Are Go Rhino running boards and side steps the same thing?

No. RB Series boards are wide, flat cab-length running boards. Go Rhino side steps are narrower OE-style steps: 4 in. and 5 in. 1000 Series, 4 in. OE Xtreme and 6 in. OE Xtreme II. See running boards vs nerf bars vs hoop steps.

Related guides