Quick answer: A hitch step slides into your truck's receiver and gives you a solid place to stand when you reach into the bed, load a roof rack or climb into a van. To pick one, match the shank size to your receiver (most steps here fit a 2 in. receiver), choose a drop that suits your truck's height, check the width and weight rating on the listing and make sure you have a hitch pin.
We carry 13 hitch steps, shanks and rear steps on our truck steps page from LUVERNE, GEN-Y Hitch, CURT, TrailFX and Body Armor 4x4. This guide compares them using the details on each product listing.
What to check before you buy
- Receiver size: the steps in this guide with a stated shank size are made for a 2 in. x 2 in. receiver.
- Drop: a drop shank lowers the step for lifted trucks and adds clearance from the bumper or spare tire. Our steps come flat or with a 4 in. or 6 in. drop.
- Width: most steps are about 26 in. wide. The GEN-Y PHANTOM XL is a 42 in. wide van step.
- Weight rating: GEN-Y lists 400 lb., 500 lb. and 600 lb. ratings. For other steps, use the rating on the product page.
- Tread: expanded-metal (Grip Step) and serrated (GEN-Y) treads grip boots in rain, mud and snow.
- Hitch pin: some steps include one and some don't. See the table.
Hitch steps compared
| Step | Build | Size | Drop | Hitch pin |
|---|---|---|---|---|
| CURT 32002 Grip Step | Aluminum, expanded-metal tread | 26 in. x 7 in. | 4 in. | Included |
| LUVERNE 415026-570015 Grip Step | Aluminum, expanded-metal tread | 26 in. (7 in. deep) | 6 in. | Included |
| TrailFX AHS002B | Aluminum, non-slip tread | See listing | 6 in. | Not included |
| TrailFX AHS001B flat step | Aluminum, non-slip tread | See listing | Flat | Not included |
| GEN-Y GH-030 | Steel, serrated, boot scraper; 500 lb. | See listing | See listing | 1 included |
| GEN-Y PHANTOM GH-13052X | Steel, serrated; 400 lb. | See listing | See listing | Not included |
| GEN-Y PHANTOM XL GH-102622 | Steel, serrated; 600 lb. | 42 in. wide (van step) | See listing | Not included |
| LUVERNE 585001 Aluminator | Aluminum, raised tread; takes 1 x 4 in. lights | 26 in. x 6 in. | See listing | Hardware included |
"See listing" means the detail isn't stated in the listing summary we checked; open the product page or contact us before ordering. GEN-Y also offers the GH-060 serrated hitch step with a boot scraper; check its listing for shank size and rating.
LUVERNE Grip Step: buy it as a set or in parts
The LUVERNE 415026 Grip Step is the 26 in. step only, so it needs a shank. The LUVERNE 570015 shank fits most 2 in. receivers, has a 6 in. drop and comes with mounting hardware and a hitch pin. The 415026-570015 set includes both. The CURT 32002 is also a Grip Step, with a 4 in. drop.
For fleet, police and work vans
- LUVERNE 585001 Aluminator: a 6 in. x 26 in. aluminum step that accepts standard 1 x 4 in. warning lights from brands like Code 3, Federal Signal, Feniex, SoundOff Signal and Whelen (lights sold separately). It's built for law enforcement and fleet use.
- GEN-Y PHANTOM XL GH-102622: a 42 in. wide serrated steel step rated for 600 lb., sold as a van step.
- Ram ProMaster: the TrailFX FBV01B rear bumper access step mounts under the rear bumper of 2014–2025 ProMaster 1500, 2500 and 3500 vans instead of using a hitch. Its listing gives a 300 lb. capacity and no-drill installation.
Hitch skid with a step
The Body Armor 4x4 Backbone Hitch Skid 5136 is a hitch protector rather than a plain step. Its listing says it guards the hitch, trailer wiring and rear bumper, adds a non-slip step and gives a recovery point, and installs with no tools.
Hitch step or side steps?
A hitch step helps at the tailgate and the roof. For getting into the cab, look at running boards or all steps and running boards, and see running boards vs nerf bars vs hoop steps and drop steps vs running boards for lifted trucks. New to receivers? Read trailer hitch classes explained and what size ball mount do I need, or shop towing.
FAQ
Can I tow with a hitch step in the receiver?
No. A receiver hitch step uses the same receiver as your ball mount, so pull the step out before you hook up a trailer.
What size receiver do hitch steps fit?
Most of the steps we carry are made for a standard 2 in. x 2 in. receiver. The LUVERNE Grip Step shank notes it may not work with some receiver adapters. Check the listing for any step that doesn't state a shank size.
Do I need a drop on my hitch step?
A drop lowers the step below the receiver. It helps on lifted trucks and gives clearance from the bumper or a rear spare tire. The CURT 32002 has a 4 in. drop, and the LUVERNE 570015 shank and TrailFX AHS002B have a 6 in. drop.
Does a hitch step come with a hitch pin?
It depends on the step. The CURT 32002, the LUVERNE 570015 shank and the GEN-Y GH-030 include a pin. The TrailFX AHS001B and AHS002B and the GEN-Y GH-13052X and GH-102622 list no pin, so buy one that fits your receiver.
How much weight can a hitch step hold?
Use the rating on the listing. The GEN-Y steps list 400 lb. (GH-13052X), 500 lb. (GH-030) and 600 lb. (GH-102622). If a listing doesn't show a rating, contact us before you rely on it.


