UWS 003-CH501CYLNDR replacement tool box paddle handle lock cylinder and keys

Quick answer: UWS makes its own replacement parts for its truck tool boxes. Start with the handle type on your box: paddle handles (most crossover, chest and side mount boxes), folding T-handles (topside, underbody, fender, drawer slide and dog boxes) or Secure Lock handles (Secure Lock crossover boxes). Keys are matched to a lock cylinder number. If you don't know your number, a new lock cylinder and key set (one cylinder, two keys) is the sure fix.

Everything below comes from the UWS listings we carry. These parts are listed for UWS boxes; for another brand's box, check with that manufacturer. See the full line on our UWS page.

Lost key or worn lock

Part UWS part # Listed for
Paddle handle lock cylinder & keys 003-CH501CYLNDR, CH502, CH505, CH506, CH507, CH508 Any UWS tool box with lockable paddle handles. One cylinder and two keys; quarter-turn lock.
T-handle lock cylinder & keys 003-RYTHCY-002, 003-RYTHCY-007 UWS fender, topside, underbody, drawer slide and dog boxes. One cylinder and two keys; quarter-turn lock.
Paddle handle replacement key KEYCH501 through KEYCH510 UWS boxes with lockable paddle handles (crossover, utility chest, side mount and more). Each key fits one cylinder number. One key per package.
Secure Lock replacement key KEYSL525, KEYSL527, KEYSL528 UWS Secure Lock boxes, including Secure Lock crossover and Secure Lock under-tonneau boxes. Each fits one cylinder number.

How to pick the right key

  • Each key fits one lock cylinder number, shown in its part number (KEYCH501 goes with cylinder CH501, KEYSL525 with SL525).
  • Look for the number on your existing key or lock before ordering.
  • Can't find it, or the lock is sticking or damaged? Replace the cylinder instead. Each cylinder set comes with its own two keys, so the number on the old lock no longer matters.

Broken or missing handle

  • UWS-LOCKING locking paddle handle: replacement for any UWS box with paddle handles; key-operated lock, polished stainless steel. Some rivet installation is required.
  • UWS-NONLOCKING non-locking paddle handle: for UWS boxes with two paddle handles (the box still needs a locking handle on the other side). Polished stainless steel; rivets required.
  • UWS-THLOCK folding T-handle: for UWS topside and underbody boxes; key-operated lock and a T-handle that folds in when not in use. Polished stainless steel; rivets required.
  • 003-SLLKBLK Secure Lock handle: for UWS Secure Lock crossover boxes; key-operated lock, powder-coated steel; rivets required.
  • UWS-ROD-CONNECT connector rod: links the two handles on a UWS box so the lid opens from either the driver or passenger side. Plated steel.
  • 003-NHPIN striker pin: the 1/4 in. pin that works with the striker bracket to latch the lid shut. Fits any UWS truck tool box.

Lid won't stay open

A UWS lid is held up by a gas lift cylinder that connects to a ball stud and a top cylinder bracket. Check all three before ordering:

  • UWS-LIFT-CYLIND: replaces any standard lift cylinder in a UWS tool box (gas spring).
  • UWS-LIFT25: the lift cylinder for UWS UTV boxes and truck side tool boxes.
  • UWS-BALL-STUD: aluminum ball stud with a threaded base; works with any UWS lift cylinder.
  • UWS-TCA top cylinder bracket: aluminum bracket on the lid that gives the cylinder its upper mounting point.
  • UWS-CABLE door cable: 12 in. stainless steel cable with eyelets for UWS topside and aluminum underbody boxes. It lets the door open a full 90 degrees and is rated to 250 lbs. on the lid. Rivet nuts and screws are required.

Leaks, rattles and mounting

  • UWS-34CLOSEDCEL lid gasket foam: 1/4 in. x 3/4 in. water-resistant, non-absorbent foam for UWS topside and underbody boxes.
  • UWS-BOXFOAM bed rail foam: 1-1/2 in. x 19-1/4 in. adhesive foam that goes between a UWS crossover box and the bed rails to protect them from scratches and galvanic corrosion.
  • UWS-JBOLTKIT J-bolt kit: two J-bolts, two washers and two nuts to hold any UWS crossover box to the bed rails.

Organization and tank parts

Replacing the whole box?

If the box itself is damaged, browse crossover, side mount, chest and underbody toolboxes, or all truck toolboxes. Our guides What size truck toolbox do I need?, Crossover truck tool box guide and Trailer tongue toolbox guide help with sizing.

FAQ

Can I get a replacement key for my UWS tool box?

Yes. Paddle handle boxes use KEYCH501–KEYCH510 keys and Secure Lock boxes use KEYSL keys. Each key fits one lock cylinder number. If you don't know the number, replace the lock cylinder; each set comes with two keys.

Why won't my tool box lid stay open?

The gas lift cylinder is the usual part to replace. On UWS boxes it attaches to a ball stud and a top cylinder bracket, and both are sold separately if they are worn or missing.

What is the difference between the locking and non-locking paddle handle?

The locking handle has a key-operated lock. The non-locking handle is for boxes with two paddle handles, where the other side still needs a locking handle.

Do UWS replacement handles need tools to install?

Yes. The listings say the paddle handles, folding T-handle and Secure Lock handle need some rivet installation, and the door cable needs rivet nuts and screws.

How-to, Toolboxes, Uws