UWS EC20391 34-inch aluminum trailer tongue tool box

Quick answer: A trailer tongue toolbox mounts on the tongue at the front of a trailer and gives you lockable, weather-resistant storage for straps, chains, binders, hitch pins and wheel chocks. Measure the open space on your tongue (length between the coupler and whatever sits behind it, and the width across the frame rails), check clearance for the jack handle, safety chains and wiring, then pick a box that fits that space. Most tongue boxes we carry are 34 inches long, in standard or low-profile heights.

What is a trailer tongue toolbox?

The tongue is the part of the trailer frame that runs forward to the coupler. On many utility, car hauler, equipment, boat and snowmobile trailers there's open space on the tongue or the A-frame that goes unused. A tongue box fills that space with a lockable box, so the gear you need every time you hook up stays with the trailer instead of rolling around in the truck bed.

Common things people keep in a tongue box:

  • Ratchet straps, chains and binders
  • Hitch pins, clips and a spare coupler lock
  • Wheel chocks and a lug wrench
  • Spare bulbs, a wiring tester and electrical tape
  • Gloves and a small tool kit

Tongue boxes we carry

Box Length Material and finish Notable features
UWS EC20391 / TBV-34 34 in. 0.058 in. one-piece aluminum tub; bright or gloss black (TBV-34-BLK) RigidCore foam-filled lid, stainless key-operated paddle handle, MicroSeal gasket, lid opens to 90 degrees on self-opening struts; fits straight-tongue or A-frame trailers
UWS EC20411 / TBV-34-LP 34 in. Same aluminum tub; bright or gloss black (TBV-34-LP-BLK) Low-profile version of the box above
TrailFX 201191 34 in. (34 x 16 x 13 in., about 2.9 cu. ft.) 16-gauge aluminum, polished diamond tread Single lockable lid with paddle handle, lid shocks, no-drill install; mounting hardware not included

Specs above come from each product page. Shop them in our toolboxes collection, or see more from TrailFX.

How to measure your trailer tongue

  1. Length: measure the open, flat run of the tongue from just behind the coupler (leave room for the latch and a coupler lock) back to the trailer's front rail, jack, or anything else mounted there.
  2. Width: on an A-frame, the rails spread apart as they go back. Measure across the rails at the spot where the box will sit, and check the box's base will rest on (or be supported across) the frame.
  3. Height: check that the lid will open fully and won't hit anything on the trailer or the load.
  4. Clearance to the tow vehicle: with the trailer hooked up, check the box won't contact the tailgate, bumper or a spare tire when you turn tight or back up at an angle.
  5. Jack, chains and wiring: make sure you can still turn the jack handle, hook up the safety chains, reach the breakaway lanyard and route the wiring.

Standard or low profile?

A standard-height box holds more. A low-profile box sits lower on the tongue, which helps when you need clearance to the tow vehicle's tailgate or want a better view over the trailer. UWS lists the low-profile versions separately (EC20411, TBV-34-LP).

Mounting tips

  • Follow the box maker's mounting instructions and use hardware rated for the job. Some boxes (like the TrailFX 201191) don't include mounting hardware.
  • Bolt or bracket the box so it can't shift, and recheck the fasteners after the first few trips.
  • Don't block the coupler latch, the jack, the safety chain attachment points or the breakaway switch.
  • Keep heavy items low and centered in the box.

Remember tongue weight

A tongue box and everything in it sit right over the coupler, so the weight adds to your trailer's tongue weight. Make sure the loaded total stays within the ratings for your hitch, ball mount, ball and tow vehicle. Our hitch class guide explains the ratings, and do I need a weight distribution hitch? covers heavier setups.

Related guides

FAQ

Will a tongue box fit a straight-tongue trailer?

Some will. UWS says its tongue boxes (EC20391, EC20411 and the TBV-34 series) fit straight-tongue or A-frame trailers. Measure the space and check how the box will be supported before you order.

Is aluminum or steel better for a tongue box?

The tongue boxes we carry are aluminum, which doesn't rust and keeps weight off the tongue. Aluminum boxes are often diamond tread or smooth with a painted or polished finish.

Do I need to drill my trailer?

It depends on the box and your trailer. TrailFX lists the 201191 as a no-drill install. Check the instructions for the box you choose.

Does a tongue box add to tongue weight?

Yes. The box and its contents add to tongue weight, so keep the total within your hitch and vehicle ratings.

Buying guide, Toolboxes, Towing